Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Cost in Burbank?
Garage door repair in Burbank typically costs $150 to $600, depending on the failure. A broken torsion spring runs $180 to $340 for a single spring, cable repair runs $130 to $250, and a full new door installation runs $700 to $2,200. Those are typical estimated ranges for this market, and the written estimate we give you after we see the door is the price that stands.
We’re a garage door specialist, not a general handyman shop. Garage doors are the trade, and nothing else. That focus matters in a town like Burbank, where most of the housing is postwar brick ranch and raised ranch stock on tight lots, and the garages behind those homes are the ones we see every day: single-car doors, low headroom, and a lot of LiftMaster, Chamberlain, and Craftsman openers that came with the house and have never been touched. Our technicians have up to 10 years of experience, we work on the brand already in your garage, and we stock parts rather than ordering them. Estimates are free, and we can often get you back to a working door the same day. Call (855) 337-1294 to get it moving.
Key takeaways
- Typical garage door repair in Burbank: $150 to $600
- A single broken spring: $180 to $340; a matched pair is usually replaced together at roughly double that
- Opener repair: $120 to $320; new opener installation: $250 to $550
- New door installation: $700 to $2,200
- Burbank’s freeze-thaw swings and older garages are the two biggest drivers of price here
- Free estimates, and the written estimate sets the final price
Garage Door Cost Breakdown (2026)
Here’s how the numbers break down for a typical Burbank job. Every figure below is an estimated range for this market, not a flat quote. Door size, opener brand, and how much of the original hardware has to come out all move the number inside those ranges.
| Service | Typical Estimated Range | What Usually Drives It |
|---|---|---|
| Garage door repair (general) | $150 – $600 | How deep the failure runs; a single part vs. several |
| Spring repair (one spring) | $180 – $340 | Spring size, cycle rating, whether it’s torsion or extension |
| Cable repair | $130 – $250 | Single cable vs. both, and whether the drum needs attention |
| Opener repair | $120 – $320 | Logic board, gear, capacitor, or a failed safety sensor |
| Opener installation | $250 – $550 | Belt vs. chain drive, smart features, and existing wiring |
| Panel replacement | $250 – $500 | Panel size and whether the style is still in production |
| Track realignment | $120 – $240 | A bent section, a pulled anchor, or a door that jumped track |
| Roller replacement | $110 – $220 | Number of rollers and whether the hinges are worn with them |
| New door installation | $700 – $2,200 | Door size, insulation, window options, and how much framing is sound |
A matched pair of springs is usually replaced together, so expect roughly twice the single-spring range for that job. We won’t quote you one spring price for a pair, and we won’t swap one spring and leave its twin to fail in a year. A broken spring on a two-spring door is a good example of a job that looks like a $200 decision and isn’t.
On the installation side, the gap between the bottom of the $700 to $2,200 range and the top is mostly about the door itself: a basic single-car non-insulated steel door sits near the low end, and a double-car insulated door with windows and a higher-end opener sits near the top. A town the size of Burbank has a lot of single-car garages, which keeps a lot of the installations on the lower half of that range. If you’re weighing repair against replacement, we’ll give you both numbers and tell you plainly which one buys you more years of a working door.
What Affects Garage Door Pricing in Burbank
- Freeze-thaw swings. Burbank winters run cold with freeze-thaw cycles through the season, and that movement works on everything from door sections to slab anchors. A door that sits level in July can drift out of alignment by February, which shows up as binding tracks, uneven gaps, and a motor that has to work harder than it should.
- Age of the housing stock. Much of Burbank’s housing went up in the postwar decades, and plenty of those garages still have original or lightly updated hardware. Older track, worn hinges, and openers that predate modern safety reversing systems all change how a job gets priced. Sometimes the fix is a part. Sometimes the smart money is a full replacement of the opener or the door.
- Low-headroom garages. A lot of Burbank garages weren’t built with generous clearance. Low headroom changes which springs and opener styles will fit, and retrofit work in a tight garage takes more labor than the same job with room to move.
- The brand already on your wall. We stock and service LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. When the opener is one of those, we know the parts chain and the failure points before we arrive, which keeps the job on the shorter end of its range. An oddball opener can push a repair up if parts have to be sourced.
- Spring type and size. Torsion and extension springs price differently, and a heavy double door takes heavier springs than a single door. The $180 to $340 range covers a single spring; the count and the size set where in that range your job lands.
- Whether the door is still in production. Panel replacements depend on the manufacturer still making your panel style. Clopay, Amarr, Wayne Dalton, and Raynor all cover a lot of older profile and panel designs, but if a panel is out of production the options shift. That’s a conversation worth having early.
One more local factor: real estate in Burbank turns over on relatively narrow 50-foot lots, and plenty of driveways are short. A short driveway means a shorter approach and less room for error when a car is parked on it, so a door that’s drifting needs to get looked at before it comes off the track entirely. That’s also why we treat spring failures as urgent rather than a “call us next week” problem.
How to Save on Garage Door
Most of the ways to keep this bill down aren’t tricks. They’re about catching a small failure before it becomes a structural one.
- Get ahead of the spring. A spring near the end of its life usually announces itself: the door gets heavy, the opener struggles, and the whole system starts sounding wrong. Servicing it early keeps you in the $180 to $340 range instead of paying for a spring plus bent track, torn cables, and panel damage.
- Fix the rollers and hinge before the opener. Worn rollers and hinges make a healthy opener act like a failing one. Spending on a $110 to $220 roller job can save you an opener repair or replacement that wasn’t the real problem.
- Replace both springs at once. Yes, a matched pair costs about twice a single spring. It usually still comes out ahead of two separate service calls months apart, and it means one job, one visit, one trip out.
- Repair the opener when the motor is sound. If the logic board or a gear is the failure, a $120 to $320 repair usually beats a $250 to $550 installation. We’ll tell you which one actually makes sense for the age of the unit, not just which one costs more today.
- Ask about panel replacement instead of a new door. A single dented or cracked panel doesn’t always mean a new door. At $250 to $500 for a panel, that’s a fraction of the $700 to $2,200 installation range, provided the style is still available.
- Insulate when you replace, not after. If a full installation is coming anyway, choosing the door you actually want the first time saves you from paying for the same install twice.
- Get a few estimates in writing. It costs you nothing and gives you something to compare. Our estimates are free, and the written estimate sets the final price. Call (855) 337-1294 to schedule one.
If you’re comparing this against a bigger picture of your home’s exterior work, the same logic applies: fix the specific problem in front of you when it’s still small. That’s why a repair page like garage door repair Ashburn reads the way it does: repair first, replace only when repair stops being the better deal.
Can you fix a broken spring the same day in Burbank?
Often, yes. Spring repair is one of our core services, and we stock the parts, so a single broken torsion or extension spring can frequently be back in service the same day. Call (855) 337-1294 as early in the day as you can, and we’ll tell you what’s realistic for a same-day visit.
A word on spring safety
Torsion and extension springs store an enormous amount of energy. When one lets go, it does so with force, and the cable, drums, and brackets around it are under real tension. We don’t encourage anyone to work on springs or cables themselves. A trained technician can release and replace a spring safely; the wrong move on a loaded spring can send someone to the hospital. What you can safely check is whether the door is balanced: lift it by hand to about halfway, and if it won’t stay put or feels unusually heavy, leave it down and call us. Don’t force it open with the opener, and don’t let anyone stand under it.
Can you come out and look at my door today?
Usually we can get to Burbank same day, and fast dispatch runs from 7am to 7pm. Estimates are free. If you’re calling because a door is stuck, off track, or the spring just snapped, say so up front and we’ll prioritize it. Call (855) 337-1294.
If the door is still moving but making new noises, that’s the other end of the scale: a lower-cost catch, and worth calling before it turns into a track or panel job.
Same-day springs, and a door that won’t close
A door hung up halfway with a snapped spring is the most common urgent call we take. The fix is usually a spring and a cable inspection, sometimes a track adjustment once the load comes off. All of that sits inside the repar range: spring at $180 to $340, cable at $130 to $250, track at $120 to $240 if a section got pulled. We’d rather you pay for two of those on one visit than have the door bend the track while you wait it out. If it’s a door that simply won’t close and the opener lights are blinking, we’ll look at the safety sensors and the logic board first, which is usually an opener repair inside the $120 to $320 range.
Is it cheaper to repair a door or replace it?
Repair is cheaper in most cases, and the dollar comparison is straightforward: a repair inside the $150 to $600 range beats a $700 to $2,200 installation almost every time. Replacement usually only wins when the door is structurally failing (rotted sections, a bent track that won’t realign, or a model where panels are no longer made) or when you’re replacing an opener that’s already past its useful life. We’ll price both for you and tell you which one we’d do.
How much does a garage door opener cost in Burbank?
A new opener installed in Burbank typically runs $250 to $550, depending on drive type and features. A repair on an existing opener runs $120 to $320. We service and install LiftMaster, Chamberlain, Genie, Craftsman, and Raynor units, so we can work with the system already in your garage. Call (855) 337-1294 for a free estimate.
If the opener is fine and the door is the problem, you’ll usually know by sound and by feel. A motor that runs without the door moving points to the spring or the drive. A door with a door motor that struggles and stops points to balance. Either way, the estimate is free, and a short visit usually gets to the bottom of it.
What’s the difference between a repair and a full installation in Burbank?
Repair keeps the door you have and fixes the failing component. Installation replaces the door, and sometimes the opener with it. If the door’s panels and track are sound, repair is almost always the lower-cost path. If the door is failing in several places at once, installation starts to make more sense. The good news is you don’t have to guess: we’ll inspect and give you both numbers.
Do you charge for estimates?
No. Estimates are free, and we’ll put the numbers in writing so you can compare. That written estimate sets the final price, which means no surprises when the job is done. Call (855) 337-1294 to schedule.
How do I know what brand my opener is?
Check the back or the inside cover of the opener housing. The brand name is usually there, and if it’s a LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, or Raynor, we already know the failure points. If you can’t find it, just read us the model number off the label when you call, and we’ll tell you what you’re working with before we arrive.
Contact us for a free estimate
Whether it’s a broken spring, a door that won’t close, or you’re trying to decide between repair and a new door, the fastest way to a real number is a call. Burbank garage door repair runs $150 to $600, spring repair runs $180 to $340, and new door installation runs $700 to $2,200, all typical estimates with a written quote to follow. We’re garage doors only, we work on the leading brands, and we stock parts so you’re not waiting on a special order.
Call (855) 337-1294 today for a free estimate. Fast dispatch from 7am to 7pm, and we can often get you back to a working door the same day. If you’re not sure what’s wrong, just describe the noise. That’s usually enough to tell us which service this is.
Written by the team at Garage Door Repair Ashburn.
Pricing reflects the Burbank market as of 2026. Garage Door Repair Ashburn offers free estimates – call (855) 337-1294.
What Our Customers Say
"Fixed the spring properly and the door works fine. He did leave the old spring and some hardware by the side of the house, and I had to text to ask about hauling it off. They came back for it, just took a couple of days."
- Ryan Mercer"Logic board on a 15 year old opener. He was upfront that a new opener would cost less than the board plus labor, and he wasn't wrong. No pressure either way."
- Marcy Doyle"Keypad stopped working, which I assumed meant a whole new system. It was the batteries and a reprogram. He charged me the minimum service call and told me how to do it myself next time."
- Adriana Guzman